Heil Quaker ICP 11201007000069 Sensor
The Heil Quaker ICP 11201007000069 Pipe Temperature Sensor is a critical OEM replacement part engineered for high-precision thermal monitoring in residential and commercial HVAC systems. As a primary thermistor-based probe, this sensor provides real-time data to the control board, ensuring the system operates within safe thermal parameters and preventing compressor damage or evaporator freeze-up. This 1/4" diameter sensor is designed for direct HVAC pipe application, featuring a durable lead wire and a probe housing optimized for rapid heat transfer and accurate resistance-to-temperature conversion.
This genuine ICP sensor is a direct replacement for various Carrier, Arcoaire, Comfortmaker, and KeepRite heat pumps and air conditioning units. For field technicians, verifying the 11201007000069 part number is essential for ensuring correct resistance curves and plug-and-play compatibility with the existing wiring harness. Reliable pipe temperature monitoring is foundational for maintaining refrigerant cycle efficiency and system safety. When diagnosing fault codes related to temperature out-of-range or sensor failure, this split system temperature sensor restores proper communication between the outdoor unit and the main controller.
Key Benefits
- OEM Compatibility: Precision-matched for ICP-branded equipment, including Heil and Carrier units, ensuring seamless integration with factory control boards.
- Enhanced System Protection: Prevents HVAC compressor overheating and system icing by providing accurate thermal feedback.
- Rapid Response Probe: High-sensitivity thermistor technology allows for near-instant detection of temperature fluctuations within the liquid or suction lines.
- Durable Construction: Built to withstand the vibrating and high-moisture environments common in condenscing units and outdoor heat pumps.
- Technical Accuracy: Reliable resistance output eliminates "ghost" fault codes caused by generic aftermarket sensors with incorrect tolerances.
Common Questions
How do I verify if the 11201007000069 sensor is faulty?
Technicians should perform a resistance check (Ohms) using a multimeter and compare the reading against the manufacturer’s temperature-resistance chart for this specific ICP sensor. An open circuit or a reading significantly outside the specified range indicates the sensor requires replacement.
Where is this sensor typically located in a heat pump?
In most split systems, this pipe temperature sensor is clipped to the refrigerant line near the outdoor coil or on the suction line to monitor discharge temperatures or prevent liquid floodback.
Can I use a universal sensor instead of this OEM part?
It is not recommended. HVAC control boards are calibrated to specific resistance curves. Using a non-OEM component can lead to incorrect temperature readings, resulting in frequent short-cycling or failure to initiate defrost cycles.
This item is not eligible for free shipping.
Disclaimer: While we strive for 100% accuracy, product data and specifications are subject to change. Please contact our team to confirm compatibility or technical details before purchasing.
Original: $5.90
-65%$5.90
$2.06Heil Quaker ICP 11201007000069 Sensor
The Heil Quaker ICP 11201007000069 Pipe Temperature Sensor is a critical OEM replacement part engineered for high-precision thermal monitoring in residential and commercial HVAC systems. As a primary thermistor-based probe, this sensor provides real-time data to the control board, ensuring the system operates within safe thermal parameters and preventing compressor damage or evaporator freeze-up. This 1/4" diameter sensor is designed for direct HVAC pipe application, featuring a durable lead wire and a probe housing optimized for rapid heat transfer and accurate resistance-to-temperature conversion.
This genuine ICP sensor is a direct replacement for various Carrier, Arcoaire, Comfortmaker, and KeepRite heat pumps and air conditioning units. For field technicians, verifying the 11201007000069 part number is essential for ensuring correct resistance curves and plug-and-play compatibility with the existing wiring harness. Reliable pipe temperature monitoring is foundational for maintaining refrigerant cycle efficiency and system safety. When diagnosing fault codes related to temperature out-of-range or sensor failure, this split system temperature sensor restores proper communication between the outdoor unit and the main controller.
Key Benefits
- OEM Compatibility: Precision-matched for ICP-branded equipment, including Heil and Carrier units, ensuring seamless integration with factory control boards.
- Enhanced System Protection: Prevents HVAC compressor overheating and system icing by providing accurate thermal feedback.
- Rapid Response Probe: High-sensitivity thermistor technology allows for near-instant detection of temperature fluctuations within the liquid or suction lines.
- Durable Construction: Built to withstand the vibrating and high-moisture environments common in condenscing units and outdoor heat pumps.
- Technical Accuracy: Reliable resistance output eliminates "ghost" fault codes caused by generic aftermarket sensors with incorrect tolerances.
Common Questions
How do I verify if the 11201007000069 sensor is faulty?
Technicians should perform a resistance check (Ohms) using a multimeter and compare the reading against the manufacturer’s temperature-resistance chart for this specific ICP sensor. An open circuit or a reading significantly outside the specified range indicates the sensor requires replacement.
Where is this sensor typically located in a heat pump?
In most split systems, this pipe temperature sensor is clipped to the refrigerant line near the outdoor coil or on the suction line to monitor discharge temperatures or prevent liquid floodback.
Can I use a universal sensor instead of this OEM part?
It is not recommended. HVAC control boards are calibrated to specific resistance curves. Using a non-OEM component can lead to incorrect temperature readings, resulting in frequent short-cycling or failure to initiate defrost cycles.
This item is not eligible for free shipping.
Disclaimer: While we strive for 100% accuracy, product data and specifications are subject to change. Please contact our team to confirm compatibility or technical details before purchasing.
Product Information
Product Information
Shipping & Returns
Shipping & Returns
Description
The Heil Quaker ICP 11201007000069 Pipe Temperature Sensor is a critical OEM replacement part engineered for high-precision thermal monitoring in residential and commercial HVAC systems. As a primary thermistor-based probe, this sensor provides real-time data to the control board, ensuring the system operates within safe thermal parameters and preventing compressor damage or evaporator freeze-up. This 1/4" diameter sensor is designed for direct HVAC pipe application, featuring a durable lead wire and a probe housing optimized for rapid heat transfer and accurate resistance-to-temperature conversion.
This genuine ICP sensor is a direct replacement for various Carrier, Arcoaire, Comfortmaker, and KeepRite heat pumps and air conditioning units. For field technicians, verifying the 11201007000069 part number is essential for ensuring correct resistance curves and plug-and-play compatibility with the existing wiring harness. Reliable pipe temperature monitoring is foundational for maintaining refrigerant cycle efficiency and system safety. When diagnosing fault codes related to temperature out-of-range or sensor failure, this split system temperature sensor restores proper communication between the outdoor unit and the main controller.
Key Benefits
- OEM Compatibility: Precision-matched for ICP-branded equipment, including Heil and Carrier units, ensuring seamless integration with factory control boards.
- Enhanced System Protection: Prevents HVAC compressor overheating and system icing by providing accurate thermal feedback.
- Rapid Response Probe: High-sensitivity thermistor technology allows for near-instant detection of temperature fluctuations within the liquid or suction lines.
- Durable Construction: Built to withstand the vibrating and high-moisture environments common in condenscing units and outdoor heat pumps.
- Technical Accuracy: Reliable resistance output eliminates "ghost" fault codes caused by generic aftermarket sensors with incorrect tolerances.
Common Questions
How do I verify if the 11201007000069 sensor is faulty?
Technicians should perform a resistance check (Ohms) using a multimeter and compare the reading against the manufacturer’s temperature-resistance chart for this specific ICP sensor. An open circuit or a reading significantly outside the specified range indicates the sensor requires replacement.
Where is this sensor typically located in a heat pump?
In most split systems, this pipe temperature sensor is clipped to the refrigerant line near the outdoor coil or on the suction line to monitor discharge temperatures or prevent liquid floodback.
Can I use a universal sensor instead of this OEM part?
It is not recommended. HVAC control boards are calibrated to specific resistance curves. Using a non-OEM component can lead to incorrect temperature readings, resulting in frequent short-cycling or failure to initiate defrost cycles.
This item is not eligible for free shipping.
Disclaimer: While we strive for 100% accuracy, product data and specifications are subject to change. Please contact our team to confirm compatibility or technical details before purchasing.
