York S1-025-47304-000 Sensor
Ensure precise defrost cycle management in heat pump systems with the York S1-025-47304-000 sensor. This OEM defrost thermistor temp sensor is specifically engineered for the York TH16 series 16 SEER modulating heat pumps, where it provides critical feedback to the control board to prevent evaporator coil icing. As a 10K Ohm NTC (Negative Temperature Coefficient) thermistor, it provides high-resolution resistance data between -40°F and +190°F to regulate system performance and maintain efficiency during low ambient conditions.
For technicians diagnosing faulty HVAC temperature sensors, the York S1-025-47304-000 is the direct replacement required for the condenser coil circuit. If you are reading infinite resistance or a value outside the standard York sensor resistance chart (approximately 11,883 Ohms at 70°F), the sensor has failed and will prevent the unit from initiating or terminating its defrost cycle correctly. This genuine York replacement restores factory-specified refrigeration performance and ensures accurate defrost cycle control without the compatibility issues associated with generic aftermarket parts.
Key Benefits:- OEM Precision: Specifically calibrated for York and Johnson Controls modulating heat pump systems to ensure exact 10K Ohm resistance values.
- System Efficiency: Prevents excessive ice accumulation on the condenser coil, maintaining optimal heat transfer and airflow.
- Plug-and-Play Compatibility: Features the factory-correct wire length and connector for rapid field replacement in TH16 series units.
- Robust Environmental Protection: Sealed thermistor bead resists moisture ingress, a common cause of corrosion and premature sensor failure.
- How can I test if this sensor is bad? Use a multimeter set to Kilo-Ohms. Measure the resistance across the sensor leads and compare the reading to a 10K Ohm NTC chart based on the current outdoor temperature.
- Will this work with older 13 or 14 SEER units? This part is specifically listed for high-efficiency modulating systems like the TH16. Always verify the part number in the manufacturer's breakdown before ordering.
- Where is this sensor typically located? It is usually clipped directly to the condenser coil or discharge line to monitor surface temperature during heating mode.
Disclaimer: While we strive for 100% accuracy, product data and specifications are subject to change. Please contact our team to confirm compatibility or technical details before purchasing.
Original: $35.85
-65%$35.85
$12.55York S1-025-47304-000 Sensor
Ensure precise defrost cycle management in heat pump systems with the York S1-025-47304-000 sensor. This OEM defrost thermistor temp sensor is specifically engineered for the York TH16 series 16 SEER modulating heat pumps, where it provides critical feedback to the control board to prevent evaporator coil icing. As a 10K Ohm NTC (Negative Temperature Coefficient) thermistor, it provides high-resolution resistance data between -40°F and +190°F to regulate system performance and maintain efficiency during low ambient conditions.
For technicians diagnosing faulty HVAC temperature sensors, the York S1-025-47304-000 is the direct replacement required for the condenser coil circuit. If you are reading infinite resistance or a value outside the standard York sensor resistance chart (approximately 11,883 Ohms at 70°F), the sensor has failed and will prevent the unit from initiating or terminating its defrost cycle correctly. This genuine York replacement restores factory-specified refrigeration performance and ensures accurate defrost cycle control without the compatibility issues associated with generic aftermarket parts.
Key Benefits:- OEM Precision: Specifically calibrated for York and Johnson Controls modulating heat pump systems to ensure exact 10K Ohm resistance values.
- System Efficiency: Prevents excessive ice accumulation on the condenser coil, maintaining optimal heat transfer and airflow.
- Plug-and-Play Compatibility: Features the factory-correct wire length and connector for rapid field replacement in TH16 series units.
- Robust Environmental Protection: Sealed thermistor bead resists moisture ingress, a common cause of corrosion and premature sensor failure.
- How can I test if this sensor is bad? Use a multimeter set to Kilo-Ohms. Measure the resistance across the sensor leads and compare the reading to a 10K Ohm NTC chart based on the current outdoor temperature.
- Will this work with older 13 or 14 SEER units? This part is specifically listed for high-efficiency modulating systems like the TH16. Always verify the part number in the manufacturer's breakdown before ordering.
- Where is this sensor typically located? It is usually clipped directly to the condenser coil or discharge line to monitor surface temperature during heating mode.
Disclaimer: While we strive for 100% accuracy, product data and specifications are subject to change. Please contact our team to confirm compatibility or technical details before purchasing.
Product Information
Product Information
Shipping & Returns
Shipping & Returns
Description
Ensure precise defrost cycle management in heat pump systems with the York S1-025-47304-000 sensor. This OEM defrost thermistor temp sensor is specifically engineered for the York TH16 series 16 SEER modulating heat pumps, where it provides critical feedback to the control board to prevent evaporator coil icing. As a 10K Ohm NTC (Negative Temperature Coefficient) thermistor, it provides high-resolution resistance data between -40°F and +190°F to regulate system performance and maintain efficiency during low ambient conditions.
For technicians diagnosing faulty HVAC temperature sensors, the York S1-025-47304-000 is the direct replacement required for the condenser coil circuit. If you are reading infinite resistance or a value outside the standard York sensor resistance chart (approximately 11,883 Ohms at 70°F), the sensor has failed and will prevent the unit from initiating or terminating its defrost cycle correctly. This genuine York replacement restores factory-specified refrigeration performance and ensures accurate defrost cycle control without the compatibility issues associated with generic aftermarket parts.
Key Benefits:- OEM Precision: Specifically calibrated for York and Johnson Controls modulating heat pump systems to ensure exact 10K Ohm resistance values.
- System Efficiency: Prevents excessive ice accumulation on the condenser coil, maintaining optimal heat transfer and airflow.
- Plug-and-Play Compatibility: Features the factory-correct wire length and connector for rapid field replacement in TH16 series units.
- Robust Environmental Protection: Sealed thermistor bead resists moisture ingress, a common cause of corrosion and premature sensor failure.
- How can I test if this sensor is bad? Use a multimeter set to Kilo-Ohms. Measure the resistance across the sensor leads and compare the reading to a 10K Ohm NTC chart based on the current outdoor temperature.
- Will this work with older 13 or 14 SEER units? This part is specifically listed for high-efficiency modulating systems like the TH16. Always verify the part number in the manufacturer's breakdown before ordering.
- Where is this sensor typically located? It is usually clipped directly to the condenser coil or discharge line to monitor surface temperature during heating mode.
Disclaimer: While we strive for 100% accuracy, product data and specifications are subject to change. Please contact our team to confirm compatibility or technical details before purchasing.
