York S1-024-39717-000 Switch
The York S1-024-39717-000 Switch is a critical OEM replacement component engineered for factory-precise monitoring of air pressure within high-efficiency HVAC systems. This two-stage pressure switch is calibrated to a 0.45 in-WC set point, specifically designed to interface with multi-stage furnace induction systems. In a professional field application, this switch acts as a safety interlock, validating that the inducer motor is moving the required volume of combustion air before allowing the ignition sequence to proceed. Its dual-stage logic supports precise low-fire operation, preventing nuisance trips and ensuring the system maintains high-efficiency performance standards.
Constructed for the rigors of mechanical rooms, the S1-024-39717-000 features a durable diaphragm and high-conductivity electrical contacts to maintain signal integrity over thousands of cycles. For York furnace repair, using this genuine York pressure switch ensures exact mounting alignment and electrical compatibility with the existing control board harness, eliminating the calibration drifts often seen with universal aftermarket alternatives. When troubleshooting two-stage HVAC systems, this switch provides the 0.45 in-WC accuracy required to satisfy the logic of York S1-024-39717-000 specifications and safeguard against blocked vents or inducer failure.
Key Benefits for Technicians:- Precise 0.45 in-WC Calibration: Specifically tuned for York two-stage furnace low-fire safety validation.
- OEM Compatibility: A direct drop-in replacement for S1-024-39717-000, ensuring zero-configuration installation.
- Enhanced System Reliability: High-quality materials resist diaphragm fatigue, reducing callbacks for intermittent pressure faults.
- Safety Compliance: Correctly identifies obstructed exhaust or intake vents to prevent unsafe combustion conditions.
What are the symptoms of a failing 0.45 in-WC pressure switch?
Technicians typically encounter flash codes on the control board indicating an "open pressure switch" fault. This often results in the inducer motor running continuously without the igniter energizing, or the system failing to transition into high-fire stages.
Can I use a universal pressure switch as a substitute for the S1-024-39717-000?
While universal switches exist, they often lack the precise 0.45 2-stage calibration required for these specific York units. Using a non-OEM part can lead to sensitive trip points that cause the system to lockout prematurely or, conversely, fail to detect a genuine venting hazard.
How do I verify the operation of this switch during a service call?
Using a digital manometer, measure the vacuum pressure at the switch port while the inducer is active. If the pressure exceeds 0.45 in-WC but the switch contacts remain open (check for continuity with a multimeter), the switch is defective and requires replacement.
Disclaimer: While we strive for 100% accuracy, product data and specifications are subject to change. Please contact our team to confirm compatibility or technical details before purchasing.
Original: $31.98
-65%$31.98
$11.19York S1-024-39717-000 Switch
The York S1-024-39717-000 Switch is a critical OEM replacement component engineered for factory-precise monitoring of air pressure within high-efficiency HVAC systems. This two-stage pressure switch is calibrated to a 0.45 in-WC set point, specifically designed to interface with multi-stage furnace induction systems. In a professional field application, this switch acts as a safety interlock, validating that the inducer motor is moving the required volume of combustion air before allowing the ignition sequence to proceed. Its dual-stage logic supports precise low-fire operation, preventing nuisance trips and ensuring the system maintains high-efficiency performance standards.
Constructed for the rigors of mechanical rooms, the S1-024-39717-000 features a durable diaphragm and high-conductivity electrical contacts to maintain signal integrity over thousands of cycles. For York furnace repair, using this genuine York pressure switch ensures exact mounting alignment and electrical compatibility with the existing control board harness, eliminating the calibration drifts often seen with universal aftermarket alternatives. When troubleshooting two-stage HVAC systems, this switch provides the 0.45 in-WC accuracy required to satisfy the logic of York S1-024-39717-000 specifications and safeguard against blocked vents or inducer failure.
Key Benefits for Technicians:- Precise 0.45 in-WC Calibration: Specifically tuned for York two-stage furnace low-fire safety validation.
- OEM Compatibility: A direct drop-in replacement for S1-024-39717-000, ensuring zero-configuration installation.
- Enhanced System Reliability: High-quality materials resist diaphragm fatigue, reducing callbacks for intermittent pressure faults.
- Safety Compliance: Correctly identifies obstructed exhaust or intake vents to prevent unsafe combustion conditions.
What are the symptoms of a failing 0.45 in-WC pressure switch?
Technicians typically encounter flash codes on the control board indicating an "open pressure switch" fault. This often results in the inducer motor running continuously without the igniter energizing, or the system failing to transition into high-fire stages.
Can I use a universal pressure switch as a substitute for the S1-024-39717-000?
While universal switches exist, they often lack the precise 0.45 2-stage calibration required for these specific York units. Using a non-OEM part can lead to sensitive trip points that cause the system to lockout prematurely or, conversely, fail to detect a genuine venting hazard.
How do I verify the operation of this switch during a service call?
Using a digital manometer, measure the vacuum pressure at the switch port while the inducer is active. If the pressure exceeds 0.45 in-WC but the switch contacts remain open (check for continuity with a multimeter), the switch is defective and requires replacement.
Disclaimer: While we strive for 100% accuracy, product data and specifications are subject to change. Please contact our team to confirm compatibility or technical details before purchasing.
Product Information
Product Information
Shipping & Returns
Shipping & Returns
Description
The York S1-024-39717-000 Switch is a critical OEM replacement component engineered for factory-precise monitoring of air pressure within high-efficiency HVAC systems. This two-stage pressure switch is calibrated to a 0.45 in-WC set point, specifically designed to interface with multi-stage furnace induction systems. In a professional field application, this switch acts as a safety interlock, validating that the inducer motor is moving the required volume of combustion air before allowing the ignition sequence to proceed. Its dual-stage logic supports precise low-fire operation, preventing nuisance trips and ensuring the system maintains high-efficiency performance standards.
Constructed for the rigors of mechanical rooms, the S1-024-39717-000 features a durable diaphragm and high-conductivity electrical contacts to maintain signal integrity over thousands of cycles. For York furnace repair, using this genuine York pressure switch ensures exact mounting alignment and electrical compatibility with the existing control board harness, eliminating the calibration drifts often seen with universal aftermarket alternatives. When troubleshooting two-stage HVAC systems, this switch provides the 0.45 in-WC accuracy required to satisfy the logic of York S1-024-39717-000 specifications and safeguard against blocked vents or inducer failure.
Key Benefits for Technicians:- Precise 0.45 in-WC Calibration: Specifically tuned for York two-stage furnace low-fire safety validation.
- OEM Compatibility: A direct drop-in replacement for S1-024-39717-000, ensuring zero-configuration installation.
- Enhanced System Reliability: High-quality materials resist diaphragm fatigue, reducing callbacks for intermittent pressure faults.
- Safety Compliance: Correctly identifies obstructed exhaust or intake vents to prevent unsafe combustion conditions.
What are the symptoms of a failing 0.45 in-WC pressure switch?
Technicians typically encounter flash codes on the control board indicating an "open pressure switch" fault. This often results in the inducer motor running continuously without the igniter energizing, or the system failing to transition into high-fire stages.
Can I use a universal pressure switch as a substitute for the S1-024-39717-000?
While universal switches exist, they often lack the precise 0.45 2-stage calibration required for these specific York units. Using a non-OEM part can lead to sensitive trip points that cause the system to lockout prematurely or, conversely, fail to detect a genuine venting hazard.
How do I verify the operation of this switch during a service call?
Using a digital manometer, measure the vacuum pressure at the switch port while the inducer is active. If the pressure exceeds 0.45 in-WC but the switch contacts remain open (check for continuity with a multimeter), the switch is defective and requires replacement.
Disclaimer: While we strive for 100% accuracy, product data and specifications are subject to change. Please contact our team to confirm compatibility or technical details before purchasing.
