Texas Furnace(Consolidated Ind) 4218501 Collector Box
The Texas Furnace (Consolidated Industries) 4218501 Collector Box is a critical combustion component designed for high-efficiency gas furnaces. As a veteran technician knows, the furnace collector box (also referred to as a condensate collector box) is responsible for gathering flue gases and residual acidic condensate before they are managed by the draft inducer motor and drainage system. This specific OEM replacement part, Texas Furnace 4218501, ensures a precise seal against the secondary heat exchanger, preventing air leaks that often cause pressure switch lockout or "air code" errors on the control board.
When diagnosing furnace leaking water from the bottom or a unit that fails to ignite due to insufficient drafting, a cracked or warped collector box is likely at fault. Plastic housing degradation over time can lead to hazardous moisture infiltration into the chassis, potentially damaging the inducer assembly or electrical components. Replacing with the 4218501 OEM part maintains the factory-specified negative pressure required for the furnace pressure switch to close reliably. This unit is built to withstand high thermal stress and corrosive condensate, making it a drop-in replacement for aging Consolidated Industries furnace models.
Key Benefits:
- Direct OEM Replacement: Matches original Texas Furnace 4218501 specifications for exact fit and alignment with the inducer boot and heat exchanger.
- Restores Combustion Efficiency: Maintains the negative pressure seal necessary to prevent intermittent ignition failures and limit switch trips.
- Corrosion Resistant: High-grade composite construction designed to handle the acidic runoff typical of high-efficiency condensation cycles.
- Prevents Structural Damage: A secure collector box prevents water leaks that otherwise lead to premature rusting of the furnace cabinet and floor.
Common Questions:
Why is my furnace leaking water near the inducer motor?
A hairline crack in the 4218501 collector box or a failing gasket is the most common cause. Condensate pools behind the housing and leaks out when the system cycles, often mistakingly diagnosed as a pump failure.
Can I use sealant to fix a cracked collector box?
While RTV can provide a temporary patch, the negative pressure and thermal cycling usually cause sealants to fail. Replacing with a new Texas Furnace collector box is the only way to ensure safe flue gas management and code compliance.
Will this part fix a pressure switch stuck open error?
If the blockage or leak is occurring within the collector housing—preventing the inducer from pulling a vacuum—then replacing this part will resolve the pressure switch issue and restore ignition.
This item is not eligible for free shipping.
Disclaimer: While we strive for 100% accuracy, product data and specifications are subject to change. Please contact our team to confirm compatibility or technical details before purchasing.
Texas Furnace(Consolidated Ind) 4218501 Collector Box
The Texas Furnace (Consolidated Industries) 4218501 Collector Box is a critical combustion component designed for high-efficiency gas furnaces. As a veteran technician knows, the furnace collector box (also referred to as a condensate collector box) is responsible for gathering flue gases and residual acidic condensate before they are managed by the draft inducer motor and drainage system. This specific OEM replacement part, Texas Furnace 4218501, ensures a precise seal against the secondary heat exchanger, preventing air leaks that often cause pressure switch lockout or "air code" errors on the control board.
When diagnosing furnace leaking water from the bottom or a unit that fails to ignite due to insufficient drafting, a cracked or warped collector box is likely at fault. Plastic housing degradation over time can lead to hazardous moisture infiltration into the chassis, potentially damaging the inducer assembly or electrical components. Replacing with the 4218501 OEM part maintains the factory-specified negative pressure required for the furnace pressure switch to close reliably. This unit is built to withstand high thermal stress and corrosive condensate, making it a drop-in replacement for aging Consolidated Industries furnace models.
Key Benefits:
- Direct OEM Replacement: Matches original Texas Furnace 4218501 specifications for exact fit and alignment with the inducer boot and heat exchanger.
- Restores Combustion Efficiency: Maintains the negative pressure seal necessary to prevent intermittent ignition failures and limit switch trips.
- Corrosion Resistant: High-grade composite construction designed to handle the acidic runoff typical of high-efficiency condensation cycles.
- Prevents Structural Damage: A secure collector box prevents water leaks that otherwise lead to premature rusting of the furnace cabinet and floor.
Common Questions:
Why is my furnace leaking water near the inducer motor?
A hairline crack in the 4218501 collector box or a failing gasket is the most common cause. Condensate pools behind the housing and leaks out when the system cycles, often mistakingly diagnosed as a pump failure.
Can I use sealant to fix a cracked collector box?
While RTV can provide a temporary patch, the negative pressure and thermal cycling usually cause sealants to fail. Replacing with a new Texas Furnace collector box is the only way to ensure safe flue gas management and code compliance.
Will this part fix a pressure switch stuck open error?
If the blockage or leak is occurring within the collector housing—preventing the inducer from pulling a vacuum—then replacing this part will resolve the pressure switch issue and restore ignition.
This item is not eligible for free shipping.
Disclaimer: While we strive for 100% accuracy, product data and specifications are subject to change. Please contact our team to confirm compatibility or technical details before purchasing.
Product Information
Product Information
Shipping & Returns
Shipping & Returns
Description
The Texas Furnace (Consolidated Industries) 4218501 Collector Box is a critical combustion component designed for high-efficiency gas furnaces. As a veteran technician knows, the furnace collector box (also referred to as a condensate collector box) is responsible for gathering flue gases and residual acidic condensate before they are managed by the draft inducer motor and drainage system. This specific OEM replacement part, Texas Furnace 4218501, ensures a precise seal against the secondary heat exchanger, preventing air leaks that often cause pressure switch lockout or "air code" errors on the control board.
When diagnosing furnace leaking water from the bottom or a unit that fails to ignite due to insufficient drafting, a cracked or warped collector box is likely at fault. Plastic housing degradation over time can lead to hazardous moisture infiltration into the chassis, potentially damaging the inducer assembly or electrical components. Replacing with the 4218501 OEM part maintains the factory-specified negative pressure required for the furnace pressure switch to close reliably. This unit is built to withstand high thermal stress and corrosive condensate, making it a drop-in replacement for aging Consolidated Industries furnace models.
Key Benefits:
- Direct OEM Replacement: Matches original Texas Furnace 4218501 specifications for exact fit and alignment with the inducer boot and heat exchanger.
- Restores Combustion Efficiency: Maintains the negative pressure seal necessary to prevent intermittent ignition failures and limit switch trips.
- Corrosion Resistant: High-grade composite construction designed to handle the acidic runoff typical of high-efficiency condensation cycles.
- Prevents Structural Damage: A secure collector box prevents water leaks that otherwise lead to premature rusting of the furnace cabinet and floor.
Common Questions:
Why is my furnace leaking water near the inducer motor?
A hairline crack in the 4218501 collector box or a failing gasket is the most common cause. Condensate pools behind the housing and leaks out when the system cycles, often mistakingly diagnosed as a pump failure.
Can I use sealant to fix a cracked collector box?
While RTV can provide a temporary patch, the negative pressure and thermal cycling usually cause sealants to fail. Replacing with a new Texas Furnace collector box is the only way to ensure safe flue gas management and code compliance.
Will this part fix a pressure switch stuck open error?
If the blockage or leak is occurring within the collector housing—preventing the inducer from pulling a vacuum—then replacing this part will resolve the pressure switch issue and restore ignition.
This item is not eligible for free shipping.
Disclaimer: While we strive for 100% accuracy, product data and specifications are subject to change. Please contact our team to confirm compatibility or technical details before purchasing.
