Carrier ZONEXX0DTS01 Sensor
The Carrier ZONEXX0DTS01 is a critical duct and heat pump temperature sensor designed specifically for integration with Carrier ComfortZone II and Zone Perfect systems. This 10k ohm thermistor provides high-accuracy discharge air temperature monitoring, allowing the zoning system controller to modulate equipment stages or activate bypass dampers based on real-time thermal loads. As a direct replacement sensor, it ensures the logic board receives precise resistance signals to prevent coil freeze-up in cooling mode or high-limit trips during heating cycles. The ZONEXX0DTS01 HVAC sensor is engineered for insertion into the supply air plenum, featuring a durable probe housing that withstands high-velocity airflow and thermal cycling. For contractors performing zoning system troubleshooting, verifying the thermistor resistance curve of this OEM component is essential for maintaining tight setpoint tolerances and optimizing HVAC system efficiency across multiple independent zones.
Key Benefits- OEM Compatibility: Specifically calibrated for Carrier zoning controllers, ensuring seamless communication and signal accuracy.
- System Protection: Acts as a primary LAT (Leaving Air Temperature) sensor to protect the compressor and heat exchanger from extreme temperature fluctuations.
- Enhanced Comfort: Provides the data necessary for precise airflow management, reducing hot and cold spots throughout the building envelope.
- Reliable Performance: Features a robust design that eliminates signal drift, common in lower-quality aftermarket thermistors.
Is the ZONEXX0DTS01 compatible with third-party zoning boards?
This sensor is a 10k ohm Type II thermistor specifically designed for Carrier and Bryant proprietary zoning systems and may not provide accurate readings on non-proprietary boards.
Where is the optimal placement for this discharge air sensor?
Technicians should install the probe in the supply air duct, downstream of the evaporator coil or heat exchanger, but before any branch take-offs or bypass ducts for the most accurate plenum temperature reading.
How do I test if the ZONEXX0DTS01 is functioning correctly?
Disconnect the sensor and measure the resistance across the leads using a multimeter; compare the Ohms to the standard 10k resistance chart at various ambient temperatures.
Disclaimer: While we strive for 100% accuracy, product data and specifications are subject to change. Please contact our team to confirm compatibility or technical details before purchasing.
Original: $99.66
-65%$99.66
$34.88Carrier ZONEXX0DTS01 Sensor
The Carrier ZONEXX0DTS01 is a critical duct and heat pump temperature sensor designed specifically for integration with Carrier ComfortZone II and Zone Perfect systems. This 10k ohm thermistor provides high-accuracy discharge air temperature monitoring, allowing the zoning system controller to modulate equipment stages or activate bypass dampers based on real-time thermal loads. As a direct replacement sensor, it ensures the logic board receives precise resistance signals to prevent coil freeze-up in cooling mode or high-limit trips during heating cycles. The ZONEXX0DTS01 HVAC sensor is engineered for insertion into the supply air plenum, featuring a durable probe housing that withstands high-velocity airflow and thermal cycling. For contractors performing zoning system troubleshooting, verifying the thermistor resistance curve of this OEM component is essential for maintaining tight setpoint tolerances and optimizing HVAC system efficiency across multiple independent zones.
Key Benefits- OEM Compatibility: Specifically calibrated for Carrier zoning controllers, ensuring seamless communication and signal accuracy.
- System Protection: Acts as a primary LAT (Leaving Air Temperature) sensor to protect the compressor and heat exchanger from extreme temperature fluctuations.
- Enhanced Comfort: Provides the data necessary for precise airflow management, reducing hot and cold spots throughout the building envelope.
- Reliable Performance: Features a robust design that eliminates signal drift, common in lower-quality aftermarket thermistors.
Is the ZONEXX0DTS01 compatible with third-party zoning boards?
This sensor is a 10k ohm Type II thermistor specifically designed for Carrier and Bryant proprietary zoning systems and may not provide accurate readings on non-proprietary boards.
Where is the optimal placement for this discharge air sensor?
Technicians should install the probe in the supply air duct, downstream of the evaporator coil or heat exchanger, but before any branch take-offs or bypass ducts for the most accurate plenum temperature reading.
How do I test if the ZONEXX0DTS01 is functioning correctly?
Disconnect the sensor and measure the resistance across the leads using a multimeter; compare the Ohms to the standard 10k resistance chart at various ambient temperatures.
Disclaimer: While we strive for 100% accuracy, product data and specifications are subject to change. Please contact our team to confirm compatibility or technical details before purchasing.
Product Information
Product Information
Shipping & Returns
Shipping & Returns
Description
The Carrier ZONEXX0DTS01 is a critical duct and heat pump temperature sensor designed specifically for integration with Carrier ComfortZone II and Zone Perfect systems. This 10k ohm thermistor provides high-accuracy discharge air temperature monitoring, allowing the zoning system controller to modulate equipment stages or activate bypass dampers based on real-time thermal loads. As a direct replacement sensor, it ensures the logic board receives precise resistance signals to prevent coil freeze-up in cooling mode or high-limit trips during heating cycles. The ZONEXX0DTS01 HVAC sensor is engineered for insertion into the supply air plenum, featuring a durable probe housing that withstands high-velocity airflow and thermal cycling. For contractors performing zoning system troubleshooting, verifying the thermistor resistance curve of this OEM component is essential for maintaining tight setpoint tolerances and optimizing HVAC system efficiency across multiple independent zones.
Key Benefits- OEM Compatibility: Specifically calibrated for Carrier zoning controllers, ensuring seamless communication and signal accuracy.
- System Protection: Acts as a primary LAT (Leaving Air Temperature) sensor to protect the compressor and heat exchanger from extreme temperature fluctuations.
- Enhanced Comfort: Provides the data necessary for precise airflow management, reducing hot and cold spots throughout the building envelope.
- Reliable Performance: Features a robust design that eliminates signal drift, common in lower-quality aftermarket thermistors.
Is the ZONEXX0DTS01 compatible with third-party zoning boards?
This sensor is a 10k ohm Type II thermistor specifically designed for Carrier and Bryant proprietary zoning systems and may not provide accurate readings on non-proprietary boards.
Where is the optimal placement for this discharge air sensor?
Technicians should install the probe in the supply air duct, downstream of the evaporator coil or heat exchanger, but before any branch take-offs or bypass ducts for the most accurate plenum temperature reading.
How do I test if the ZONEXX0DTS01 is functioning correctly?
Disconnect the sensor and measure the resistance across the leads using a multimeter; compare the Ohms to the standard 10k resistance chart at various ambient temperatures.
Disclaimer: While we strive for 100% accuracy, product data and specifications are subject to change. Please contact our team to confirm compatibility or technical details before purchasing.
